239-662-5454
Welcome to Blue Seas Marine Online
info@blueseasmarinestore.com
  • Victron SmallBMS f\/Smart LiFePO4 Batteries w\/M8 [BMS400100000]
  • Victron SmallBMS f\/Smart LiFePO4 Batteries w\/M8 [BMS400100000]
  • Victron SmallBMS f\/Smart LiFePO4 Batteries w\/M8 [BMS400100000]

    • Victron SmallBMS f/Smart LiFePO4 Batteries w/M8 [BMS400100000]

    Victron Energy

    MSRP: $58.00
    $49.30
    (You save $8.70 )
    (No reviews yet) Write a Review
    SKU:
    BSM-92772
    UPC:
    8719076043485
    Width:
    6.00 (in)
    Height:
    2.00 (in)
    Depth:
    7.00 (in)
    MPN:
    BMS400100000
    Adding to cart… category.add_cart_announcement

    Product Description

    SmallBMS for Smart LiFePO4 Batteries with M8

    A simple and low-cost alternative to the VE.Bus BMS. The smallBMS can replace the VE.Bus BMS in several applications. It is however not suitable for use with VE.Bus MultiPlus and Quattro inverter/chargers: it has no VE.Bus interface.

    The smallBMS is intended for use with Victron Smart LiFePo4 batteries with M8 circular connectors. The smallBMS has three outputs, similar to the VE.Bus BMS. Load Disconnect output The Load output is normally high and becomes free-floating in case of the cell under voltage (default 2,8V/cell, adjustable on the battery between 2,6V and 2,8V per cell). Maximum current: 1A. The Load output is not short-circuit protected.

    The Load output can be used to control:

    • A high current relay or contactor.
    • The remote on/off the input of a Battery Protect, inverter or DC-DC converter, or other loads.

    Pre-alarm output

    The pre-alarm output is normally free-floating and becomes high in case of the imminent cell under voltage (default 3,1V/cell, adjustable on the battery between 2,85V and 3,15V per cell). Maximum current: 1A (not short circuit protected).

    The minimum delay between pre-alarm and load disconnect is 30 seconds.

    Charge disconnect output

    The Charger output is normally high and becomes free-floating in case of imminent cell overvoltage or over-temperature. Maximum current: 10mA. The Charger output is not suitable to power an inductive load such as a relay coil. 

    The Charger output can be used to control:

    • The remote on/off of a charger
    • A Cyrix-Li-Charge relay
    • A Cyrix-Li-ct Battery Combiner

    System on/off input

    The system on/off input controls both outputs. When off, both outputs will be free floating so that loads and chargers are turned off. The System on/off consists of two terminals: Remote L and Remote H. A remote on/off switch or relay contact can be connected between L and H. Alternatively, terminal H can be switched to battery plus, or terminal L can be switched to battery minus.

    Protects 12V, 24V and 48V systems

    Operating voltage range: 8 to 70V DC.

    LED indicators:

    • Load ON (blue): Load output high (cell voltage >2.8V, adjustable on the battery).
    • Temp or OVP (red): Charger output free floating (due to cell over temperature (>50°C), cell under temperature (<5 °C) or cell over voltage).
    Please contact your dealer for any returns, repairs or support issues related to this product.


    Quick Guide (pdf)
    Brochure (pdf)

    Product Videos

    Custom Field

    MPN BMS400100000

    Product Reviews

    Write a Review